Products
Home > AST Homemade Produc... > Carbide Endmills > Endmill Square > LEM Long Neck Endm... > LEM2-STA
|
|
LEM Long Neck Solid Carbide End Mill with Two Cutting Edges ---Basic Type
Features:
1、All dimension is fixed by our norm and also accept non standard order.
2、Tolerance of dc≤Φ0.15 0/-0.01, dc＞Φ0.15 0/-0.015;
3、Tolerance of shank h6
4、Cutting edge to center with tip angle;
5、Dimension of chamfer on the corner C value:
D≤Φ3，C=0.02～0.1；D＞Φ3， C=0.1；
6、Helix angle 35°.
7、Shank taper angle β, dc＜0.2 β=11°, others β=16°.
Universal Endmills-High-performance Type/Basic Type/Economical Type
Application Variety
Features--of HTA Series High-performance Endmills:
□ Carefully selected High-strength carbide and coating cemented carbide, improve the oxidation resistance, heat resistance, wear resistance.
□ Fewer macroparticles on film surface result in improved smoothness. Reduced abrasion and better deposition resistance improved wear and adhesion resistance.
□ Unique geometry improves chip removal and tools rigidity. So the tools can machine≤HRC55 following materials: stainless steel, heat-resistant alloys, titanium, nickel alloys, cast iron, copper alloys, etc.
□ High performance carbide material ensure longer tool life and high efficiency.
Features--of STA Series Basic Type Endmills:
□ Carefully selected High-strength carbide and coating cemented carbide, improve the oxidation resistance, heat resistance, wear resistance.
□ Superior chipping, wear resistance，and better surface roughness from special cutting edge and margin shape .
□ Aplly to very wide work materials.
□ STA：economical and high performance carbide meterial.
Features--of ST Series Economical Type Endmills:
□ Better heat and wear resistance from ST coating for a long life.
□ Aplly to very wide work materials.
□ Superior chipping, wear resistance，and better surface roughness from special cutting edge and margin shape .
□ Economical and high performance carbide material.
Application Work Material:
| Series | Work Material | |||||||||||||
| Structural Steel | Carbon Steel | Alloy Steel | Pre-hardened Steel | Hardened Steel | Stainless Steel | Titanium Alloys, Nickel Alloys | Cast Irons | Aluminum Alloys | Copper Alloys | Plastic | ||||
| HRC30-45 | HRC45-55 | HRC55-60 | >HRC60 | |||||||||||
| ST |
◎ |
◎ |
◎ |
◎ |
◎ |
|
|
|
○ |
|
○ |
|
○ |
|
| STA | ◎ | ◎ | ◎ | ◎ | ◎ |
○ |
◎ |
○ |
◎ |
|
○ |
|
||
| HTA |
◎ |
◎ |
◎ |
◎ |
◎ |
◎ |
|
|
◎ |
◎ |
◎ |
|
○ |
|
(◎ Most Suitable ○ Suitable)
Difference between ST/STA/HTA Series:
| Series | Design of cutting edge | Carbide Material | Coating |
| ST | Unique shape of cutting edge suitable for very wide work materials | Economical carbide material | Economical universal coating |
| STA | Unique shape of cutting edge suitable for very wide work materials | Normal carbide material | High-performance coating especially suitable for endmills |
| HTA | Unique shape of cutting edge suitable for very wide work materials | High-performance carbide material | High-performance coating especially suitable for endmills |
Type available and Diameter ranges
EM2：D1.5~32.0mm EM3：D2.0~32.0mm EM4：D4.0~32.0mm
LEM2：D2.0~4.0mm LEM4：D2.0~6.0mm
REM2：D1.0~20.0mm REM4：D3.0~20.0mm
LREM2：D2.0~6.0mm LREM4：D3.0~12.0mm
BEM2：R1.0~6.0mm BEM3：R2.0~16.0mm BEM4：R2.0~16.0mm
LBEM2：R1.0~2.0mm
| Basic type Order No. | Cutting EdgeDiameter | Flute Length | Effective Length | Shank Diameter | Shank Diameter | Overall Length |
| STA Series (Coating) | dc | lc | lf | dl | ds | lo |
| LEM2020060STA | 2.0 | 3 | 6 | 1.91 | 4 | 45 |
| LEM2020080STA | 2.0 | 3 | 8 | 1.91 | 4 | 45 |
| LEM2020100STA | 2.0 | 3 | 10 | 1.91 | 4 | 45 |
| LEM2020120STA | 2.0 | 3 | 12 | 1.91 | 4 | 45 |
| LEM2020140STA | 2.0 | 3 | 14 | 1.91 | 4 | 50 |
| LEM2020160STA | 2.0 | 3 | 16 | 1.91 | 4 | 50 |
| LEM2020180STA | 2.0 | 3 | 18 | 1.91 | 4 | 55 |
| LEM2020200STA | 2.0 | 3 | 20 | 1.91 | 4 | 55 |
| LEM2030100STA | 3.0 | 4.5 | 10 | 2.92 | 6 | 45 |
| LEM2030120STA | 3.0 | 4.5 | 12 | 2.92 | 6 | 50 |
| LEM2030140STA | 3.0 | 4.5 | 14 | 2.92 | 6 | 50 |
| LEM2030160STA | 3.0 | 4.5 | 16 | 2.92 | 6 | 60 |
| LEM2030180STA | 3.0 | 4.5 | 18 | 2.92 | 6 | 60 |
| LEM2030200STA | 3.0 | 4.5 | 20 | 2.92 | 6 | 60 |
| LEM2040120STA | 4.0 | 6 | 12 | 3.82 | 6 | 50 |
| LEM2040160STA | 4.0 | 6 | 16 | 3.82 | 6 | 60 |
| LEM2040200STA | 4.0 | 6 | 20 | 3.82 | 6 | 60 |
| LEM2040250STA | 4.0 | 6 | 25 | 3.82 | 6 | 70 |
